There are currently no product reviews.
Parts for fan gearbox
Replacement main gears have 6-spline hub instead of the round hub in drawing on TAV.C27
Fan shaft for comer D-7 gearbox has 15 tooth gear and is 10-1/4 inches long. 707.336 Normally paired with 60 tooth 5-3/4 inch diameter C387161 main...
Main gear for D-7 gearbox. 60 tooth 5-3/4 inch diameter for 6-spline input shaft. Usually paired with C006126 fan shaft.
Ball bearing for fan shaft on D-7 gearbox
Ball bearing for D-7 input shaft.
Oil seal for D-7, Mtpx, and RRG Gearbox. Measures 35 x 72 x 10 mm
3/8 bsp clear plastic plug for DS-7 and Mtpx gearboxes
8-1/4 inch long input shaft for D-7 has 6 spline on each end.
62 tooth 5-7/8 inch diameter main gear with 6-spline center for D-7 gearbox.
3/8 inch bsp fill plug has built in vent.
3/8 inch bsp tapered galvanized plug has square head.
Clear plug fits inside 32 mm hole in car 3 case.
Neutral Lever for Car 3 and MTP gearboxes. Block has 2 indentations on back to accommodate ball and spring inside case.
Fan shaft with 18 tooth gear for later model gearbox with aluminum case. This shaft has angle cut gear and will not work with flat cut main gears
Car 3 rear case housing. Has 2 inch hole at top and 1-3/4 inch opening at bottom.
Shifter block with two beveled sides for less interference. Fits MTPX and other gearbox's.
Shifter block with one beveled side. Fits MTPX and other gearbox's.
Neutral lever used inside Car-3 (aluminum case) gearbox.
Rubber coated metal plug for Mtpx gearbox allows access to fan shaft.
6-spline Input shaft for Mtpx gearbox.
1/2 inch bsp galvanized plug with square head.
6-7/8 inch diameter x 1-1/8 thick main gear with 75 bevel cut teeth. 35 mm center with 2 keyways.
Ball bearing used in D-7 gearbox uses 2, one on each shaft next to oil seal. Te-55 and Te-71 pumps also use 1 - C154017 bearing per pump.
Housing for Mtpx gearbox used on 32 - 36 inch Turbofans and most Cannon and Flexgun sprayers.
8 inch long Input shaft for RRG gearbox has dual key ways
9 inch diameter 81 tooth main gear for RRG gearbox.
19 tooth gear for RRG gearbox.
6 inch long input shaft for MTM gearbox.
9-3/4 inch diameter main gear for MTM gearbox
Controls placement of small gear on MTM gearbox.
Neutral lever for outside of MTM gearbox. Has 16 mm diameter hole in center, some models require drilling this handle to 18 mm.
MTP gearbox has 732 or 733 stamped on case. Parts listing is TAV.9A
7 inch long shaft for MTP gearbox TAV. 9a
11 inch Fan Shaft for MTP gearbox uses 24 mm fine thread nut.
11 inch fan shaft for MTP gearbox uses 24 mm coarse threaded nut
77 tooth 7 inch diameter main gear for MTP gearbox with 35 mm center.
17 tooth pinnon gear for MTP gearbox
Neutral lever for MTP (TAV.9A) and other gearboxes.
Neutral lever used inside MTP and Car-3 (aluminum case) gearbox's
Tav.89b is the old MTPX gearbox. Item number 7 case half has is different at the top compared to item number 5 on Tav.9a MTP gearbox.
14-3/4 inch long fan shaft for old style mtpx gearbox on Tav. 89b
Copyright © 2018 Leinbachs Inc. Powered by Zen Cart