There are currently no product reviews.
Screw for older model K80 blower units
1502/04 backup washer for use with rivet kit if extra reinforcement is needed.
Plastic screw holds visor hinge to helmet shell.
4 amp slow blow fuse. Measures 3/4 inch in length.
2.5 amp slow blow fuse. Measures 3/4 inch in length.
10 amp slow blow fuse. Measures 3/4 inch in length.
Short rivet kit (0604/03) for Kasco respirator helmets. Measures 5/16 inches long by 3/16 inches in diameter.
Long rivet kit (0604/12) for Kasco respirator helmets. Measures 3/8 inches long by 3/16 inches in diameter.
Inserts into back of K80S helmets to connect air hose. Inspect this part for cracks if your hose does not stay in helmet.
Hinge washer to attach visor to helmet shell. 35 mm ( 1 1/3 inch) O.D. Use 1901008 Screw
Grid holds pre-filter (1307008) to main filter.
Socket with 2 pin connector to convert from old 4 pin design on older model Prof 88 model helmets.
Prefilter prolongs life of filter. Photo shows prefiter with grid attached to filter. Use 0705006 grid to attach to filter.
Over pressure relief vent for all Kasco helmets
Gasket fits all K80S helmet shells. Visor seats on gasket in closed position.
Adapter fit T-9-T-5 and T-4 helmets allowing the use of two filters
Cigarette lighter socket with 28 mm mounting hole and rubber cover.
Prof-88 helmet power switch.
Headband fits all K80S (T-1 to T-9)
Close out prices on polyammide fabric- water resistant medium spray suits. One piece suit zips up the front. No longer available from Kasco.
Close out prices on polyammide- water resistant small spray suits. One piece suit zips up the front. No longer available from Kasco.
Adjustable belt for K80S blower motor.
Back cover with input jack for T-1 and T-7 blower motors.
Breather hose from blower to helmet for use with T-1- T-7- and older T-5 model K80S model helmets.
Old style Tractor socket with hinged cover.
Test air-flow on your older model K80S-T1- T-5- and T-7 units. Make sure your blower motor and batteries are working properly. Unit has floating ball...
ZP3 - HEPA dust filter for all Kasco helmets.
Make your own replacement cables. This 32 inch long cable will solder directly to 0701013 old style T-5 motor- or solder to a 1603003 to make a T-9...
Test air flow on your K80S-T8 and K80S-T9 with this easy to use gauge. Has floating ball and calibration mark showing 6 cubic feet per minute....
Connects 6 volt battery to blower motor
Twelve foot 12 volt power supply cable (0309/09) for older model T-4 and T-7. Used the same as six foot cable. Can also be used as extension cord for...
Prof-88 Headband with chinstrap.
Breather hose from blower to helmet for K80S T-8 and T-9 models. Has quarter turn lock at blower motor end.
Six foot 12 volt power supply cable for T-1- T-4- and T-7 model Kasco systems. Can also be used as an extension cord on models with 1301006 tractor...
ZA2P3 Filter for Prof-88 helmet
ZA2P3 filter for organic vapors- pesticides- dusts- fumes- and mists. Fits all Kasco respirators. Niosh approved.
Prof-88 air flow gauge. Calibrated for use on the suction side of filter. Tests condition of motor- batteries- and dust filter to ensure safe...
Clear visor for all K80S model (T-1 through T-9) Kasco helmets.
Blue collar for all K80S helmets. Includes drawstring and hardware.
T-9 power cable has cigarette lighter type plug for power outlet and 2-prong plug at motor end.
Blue collar with built in exhaust vents for newer model Prof 88 helmet.
12 volt power cable has fused cigarette lighter type plug end for power outlet and two prong plug at blower motor end. For use with K80S T9-R model...
6-volt motor with solder connectors for older model T-5 blowers.
Replacement Ni-Cad battery pack for K80S T-7 blower motor.
12 volt blower motor for Prof 88 model helmets.
Replacement electic motor with solder connectors for rechargeable T9-R blower assembly(0303076).
Tinted visor fits all Kasco helmets.
Circuit board for older model T-1 with multi-speed blower.
Circuit board for K80S-T7 supports multispeed blower and controls automatic recharging of the ni-cad batteries.
Prof 88 - 12 volt replacement battery pack. For models with NC9-2 on power supply- the 9-2 stands for 9 batteries spot welded together and the 2...
12 volt to 6 volt. Operate your 6 volt K80S-T8 from your 12 volt Tractor.
T-8 battery charger model BP-6. Automatically switches to maintenance charge once battery reaches 80% capacity.
12 volt T-4 blower motor (03030010) is older version of T-9 motor and uses 0309002 hose and 0309003 cable.
6 Volt - 6 amp hour battery for K80S-T8 helmet.
T-7 Blower motor has built in batteries that automatically recharge while using- so operator can disconnect from power source to re-fill sprayer....
12 volt T-9 Blower unit for K80S-T9 system. Niosh approved.
$398.36... more info
0601/13 Turbo-1AP filter for use in tractor cab installed filter system. Measures 25 1/2 inches long- 9 inches wide and 2 1/4 inches high. Sealed in...
6 volt T-8 Blower unit for K80S-T8. Niosh approved.
Blower motor has built in rechargeable ni-cad batteries. The batteries allow unit to run for short periods of time unplugged from tractor.
$601.76... more info
Complete fiberglass helmet shell with adjustable headband- collar- and visor. Fits all K80S models T-1 through T-9.
This tractor-powered spray helmet is NIOSH 23-C approved and is ideal for both orchard spraying and fieldwork. Comes complete with 2 ZA2P3 filter...
Operates from 6 volt battery (included) and has 4-hour running time. NIOSH 23-C approved. Ideal for both greenhouse and fieldwork. An optional second...
Copyright © 2018 Leinbachs Inc. Powered by Zen Cart